Omni Pump International Limited t/a Edincare Pumped Drainage Sys
 01442 211 554
 
Product Search:   Go

PowerFlushPro


View larger image

Price: £540.00 (£648.00 inc. VAT)
1003
6-10 working days
12 months

 
Description
Downloadable Documents

The PowerFlushPro is a fully automatic macerator incorporating a built in high level alarm suitable for pumping waste from a complete bathroom to a higher level when gravity drainage is not possible or economical to install.
 
The system is suitable for installing either at the initial building stage or retro fitting to existing buildings and can accept waste connections from a toilet, basin, shower or bidet.

The system is supplied as standard with a built in high level alarm and volt free output allowing fault alerts to be transmitted to a building management system of similar. The inlet location is variable allowing greater versatility of installation.

The PowerFlushPro incorporates the unique Piranha® cutting system – its razor sharp stainless steel blades act like a pair of rotary scissors to cut up waste items, reducing the chance of a blockage.

The PowerFlushPro is compact and easy to install, discharging to the right or left.

Dimensions 

Model Length Width Height
PowerFlushPro 506mm 215mm 293mm

 

Specification

Model PowerFlushPro
Power Supply 230V AC
Rated Current 4.6A
Motor Rating 1000W
Frequency 50Hz
Revolutions per Minute 2900rpm
Max. Vertical Output 10m
Max. Horizontal Output 70m
Horizontal Fall 1:200
Max. Flow Rate 120 l/m
Max. Liquid Temp. <60°C intermittent
Discharge Size 32mm
Cable Length 1.8m
Weight 7kg
Colour White

Installation guidelines
It is important to note that these instructions are for guidance only. Please refer to the full Installation and Operating Guidelines when specifying / installing the product.

Siting the product
The unit is designed for a direct toilet connection and so should be positioned behind the toilet on a firm level surface, resistant to condensation. It is extremely important to site the PowerFlushPro with access in mind in the event of maintenance being required.

Inlet connections
The PowerFlushPro comes complete with 2no WC pan connections, one to be blanked off, and 2no 50mm connections for additional appliances. To connect the toilet to the WC connection you must position the toilet in front of the unit and pull the black rubber sealing sleeve directly onto the toilet outflow spigot ensuring as much of the spigot as possible is covered. To connect additional appliances (i.e. basin, shower, bidet etc.) there is a low level inlet on either side of the unit. The inlets are designed to accept 50mm uPVC waste pipe, however if you wish to use 32mm uPVC waste pipe there are fittings provided to do so.

Discharge connection
The discharge line can be connected to the PowerFlushPro on either the left or the right hand side of the unit.The non-return valve should be connected to the discharge port being used, using the jubilee clips provided.The discharge pipework should be 32mm uPVC waste pipe and all joins should be made using solvent cement, under no circumstances should push fit or compression fittings be used.The PowerFlushPro is designed for one lift only and the vertical lift should be within 500mm of the unit. 

IMPORTANT – It is recommended that there are no bends in the vertical lift, however if this is unavoidable a minimum of slow radius bends may be used.

Electrical connection
A qualified person in accordance with the Institute Of Electrical Engineers Regulations should connect the unit to the appropriate mains supply taking into account all the electrical information provided.

IMPORTANT – All pump systems must be used with an appropriate motor rated protection device.

Maintenance
It is recommended that the PowerFlushPro be flushed through every two weeks using standard domestic bleaches, WC cleansers, etc.

IMPORTANT – The following items must not be disposed of into the PowerFlush:
• Cotton Wool Buds,
• Baby Wipes,
• Any hard objects, i.e. wood, metals, plastics etc.,
• Any fibrous materials such as cloths, rags etc.,
• Or similar.

Health & safety
As with all site work, the danger of working with water and electricity can pose a severe threat to health if obvious and fundamental precautions are not taken. Therefore if you are in any doubt regarding the installation, please contact us.

All site work must be undertaken by qualified personnel only.

These notes are for guidance only and it is for the installer to ensure the installation is in accordance with all structural and regulatory requirements.

Our policy is one of continuous product improvement, we reserve the right to change specifications and prices without prior notice. All information is given in good faith.

Loading...