MagnaPro Twin Vortex (360 Model)

Home

Packaged Pumping Stations

Description

Downloadable Documents

Related products

The MagnaPro 360 Twin Vortex is a fully automatic pumping station specifically designed for pumping both foul and storm water when gravity drainage is not possible or economical to install.

The system is suitable for installing either at the initial building stage or retro fitting to existing buildings and can accept waste from a basement, entire house/s or similar.

The system consists of a polyethylene tank, locking access cover, internal pipework and fittings, control panel, float switches with two built in vortex submersible pumps.

The MagnaPro Twin 360 Vortex is easy to install as inlets can be positioned to your requirements (inlet information to be supplied at time of order).

200–360 litre storage capacity (depending on inlet level)

Dimensions

Model	Diameter	Height
MagnaPro 360 Twin Vortex	850mm	1250mm

Specification

Model	Magna360Pro
Power Supply	230V AC
Rated Current	7.3A
Motor Rating	1100W
Frequency	50Hz
Revolutions per Minute	2800rpm
Max. Vertical Output	11m
Max. Horizontal Output	100m
Max Flow Rate	600 l/m
Max. Liquid Temperature	<40°C
Discharge Size	63mm OD
Cable Length	10m
Weight	95kg
Colour	White

Also available in Three Phase (400V AC) and both single/twin pump setups. Please call for technical specifications.

Installation guidelines
It is important to note that these instructions are for guidance only. Please refer to the full Installation and Operating Guidelines when specifying / installing the products.

Siting the product
The MagnaPro 360 Twin Vortex is designed to be installed below ground level and so the prevailing ground conditions must be considered prior to locating the unit. Where possible, installation of a pumping station in a roadway should be avoided due to the need for periodic maintenance of the pump contained therein. If the location is adjacent to a roadway, the installation method should take into account the imposed loads likely to be transmitted to the tank by traffic etc.

The MagnaPro 360 Twin Vortex should be positioned in a sump with sufficient dimensions to allow for a concrete surround.

Inlet connection
The MagnaPro 360 Twin Vortex comes complete with a 110mm rubber connector located on the side of the tank that will accept 110mm uPVC soil waste pipe. The waste pipe needs to be run with sufficient gradient to allow the waste to gravity drain into the unit and should be pushed firmly into the 110mm rubber connector so as to form a watertight seal around the incoming pipe.

NOTE – Inlets can be positioned to your requirement but must be specified at time of order.

Discharge connection

The connection of the discharge line is via the supplied compression adaptor. This connector is designed to accept black MDPE / MDPE pipework of appropriate outer diameter.

Electrical connection
A qualified person in accordance with the Institute Of Electrical Engineers Regulations should connect the unit to the appropriate mains supply taking into account all the electrical information provided.

IMPORTANT – All pump systems must be used with an appropriate motor rated protection device.

Maintenance
We recommend that the unit be inspected every three months. The inside of the MagnaPro 360 Twin Vortex should be inspected to ensure the floats are clean and free of any build up of materials that may inhibit the operation of the float switch. Also the moving parts of the pump should be checked to ensure that they are moving freely. Hose down the interior of the tank if necessary to remove any build up of solid materials and the bottom of the tank should be checked to make sure there is no debris or materials that could enter the pump and cause irreparable damage.

In addition we recommend that a service agreement be taken out with a technically qualified company.

Health & safety
As with all site work, the danger of working with water and electricity can pose a severe threat to health if obvious and fundamental precautions are not taken. Therefore if you are in any doubt regarding the installation, please contact us.

All site work must be undertaken by qualified personnel only.

These notes are for guidance only and it is for the installer to ensure the installation is in accordance with all structural and regulatory requirements.

Our policy is one of continuous product improvement, we reserve the right to change specifications and prices without prior notice. All information is given in good faith.