Omni Pump International Limited t/a Edincare Pumped Drainage Sys
 01442 211 554
Product Search:   Go

MaestroSanisplit Pro

View larger image

Price: £675.00 (£810.00 inc. VAT)
4-5 working days
12 months

Downloadable Documents
Related products

The MaestroSanisplit Pro is a fully automatic macerator suitable for pumping waste from a complete bathroom to a higher level when gravity drainage is not possible or economical to install.

The system is suitable for installing either at the initial building stage or retro fitting to existing buildings and can accept waste connections from a toilet, basin, shower or bidet.

The system is ideal for commercial applications such as hotels and guesthouses, as standard domestic macerators are prone to blockages due to abuse leading to loss of revenue. The MaestroSanisplit Pro consists of two modules, the collection tank and detachable pump module. Should a blockage occur the pump module can be removed for servicing and immediately replaced with a spare. This means that within minutes the system is fully operational.


MaestroSanisplit Pro

MaestroSanisplit Pro
Power Supply
230V AC
Rated Current
Motor Rating
Revolutions per Minute
Max. Vertical Output
Max. Horizontal Output
Horizontal Fall
Max. Flow Rate
135 l/m
Max. Liquid Temp.
<60°C intermittent
Discharge Size
Cable Length

Installation guidelines
It is important to note that these instructions are for guidance only. Please refer to the full Installation and Operating Guidelines when specifying / installing the product.

Siting the product
The unit is designed for a direct toilet connection and so should be positioned behind the toilet on a firm level surface, resistant to condensation. It is extremely important to site the MaestroSanisplit Pro with access in mind in the event of maintenance being required.

Inlet connections
The MaestroSanisplit Pro comes complete with 1no. WC pan connection and 2no. 32/40mm connections for additional appliances.

To connect the toilet to the WC connection you must position the toilet in front of the unit and pull the black rubber sealing sleeve directly onto the toilet outflow spigot and securing it in place using the 100mm jubilee clip provided.

To connect additional appliances (i.e. basin, shower, bidet etc.) there are two inlets to the rear of the unit which accept 32mm or 40mm uPVC waste pipe which should be secured in place using the jubilee clips provided.

Discharge connection
The discharge line must be connected to the top rubber connector at the rear of the unit using 32mm uPVC waste pipe and fixed into place using a jubilee clip.

All joins in the discharge line must be made using solvent cement, under no circumstances should push fit or compression fittings be used.

The MaestroSanisplit Pro is designed for one lift only and this vertical lift should be within 500mm of the unit.

IMPORTANT – It is recommended that there are no bends in the vertical lift, however if this is unavoidable a minimum of slow radius bends may be used.

Electrical connection
A qualified person in accordance with the Institute Of Electrical Engineers Regulations should connect the unit to the appropriate mains supply taking into account all the electrical information provided.

IMPORTANT – All pump systems must be used with an appropriate motor rated protection device.

It is recommended that the MaestroSanisplit Pro be flushed through every two weeks using standard domestic bleaches, WC cleansers, etc.

IMPORTANT – The following items must not be disposed of into the MaestroSanisplit Pro:
• Cotton Wool Buds,
• Baby Wipes,
• Any hard objects, i.e. wood, metals, plastics etc.,
• Any fibrous materials such as cloths, rags etc.,
• Or similar.

Health & safety
As with all site work, the danger of working with water and electricity can pose a severe threat to health if obvious and fundamental precautions are not taken. Therefore if you are in any doubt regarding the installation, please contact us.

All site work must be undertaken by qualified personnel only.

These notes are for guidance only and it is for the installer to ensure the installation is in accordance with all structural and regulatory requirements.

Our policy is one of continuous product improvement, we reserve the right to change specifications and prices without prior notice. All information is given in good faith.