Omni Pump International Limited t/a Edincare Pumped Drainage Sys
 01442 211 554
Product Search:   Go

AutoFlush 90 XL

View larger image

Price: £695.00 (£834.00 inc. VAT)
2-3 working days
12 months

Downloadable Documents
Related products

The AutoFlush 90 XL is a fully automatic waste water pumping system suitable for pumping grey water to a higher level when gravity drainage is not possible or economical to install.

The system is suitable for installing either at the initial building stage or retro fitting to existing buildings and can accept waste connections from a domestic sink, washing machine, dishwasher or similar.

The system consists of a polyethylene odour tight tank with a built in automatic waste water submersible pump.

The AutoFlush 90 XL is easy to install as inlets can be positioned to your requirements (inlet information to be supplied at time of order).

90 litre storage capacity



Power Supply
230V AC
Rated Current
Motor Rating
Revolutions per Minute
Max. Vertical Output
Max. Horizontal Output
Horizontal Fall
Max. Flow Rate
240 l/m
Max. Liquid Temp.
Discharge Size
Cable Length

Installation guidelines
It is important to note that these instructions are for guidance only. Please refer to the full Installation and Operating Guidelines when specifying / installing the product.

Siting the product
The AutoFlush90 XL should be positioned on a firm level surface, resistant to condensation. The unit must be located lower than the outflow of the appliances served so as to provide a gravity fall into the unit.

It is extremely important to site the AutoFlush90 XL with access in mind in the event of maintenance being required.

Inlet connections
The AutoFlush90 XL comes as standard complete with 1no. 32mm rubber connector located on the lid of the unit.

The rubber inlet connector is designed to accept 32mm uPVC waste pipe and should be pushed approximately 40mm into the connector which will then form a watertight seal around the incoming waste pipe.

NOTE – Inlets can be positioned on the AutoFlush 90 XL to suit your site requirements (details on inlet positions must be supplied when ordering).

Discharge connection
The discharge line must be connected to the AutoFlush 90 XL via the tank connector on the side of the unit. The tank connector will accept 32mm uPVC waste pipe.

All joins in the discharge line must be made with solvent cement, under no circumstances should push fit or compression fittings be used.

The AutoFlush 90 XL is designed for one lift only and the vertical lift should be within 500mm of the unit.

IMPORTANT – It is recommended that there are no bends in the vertical lift, however if this is unavoidable a minimum of slow radius bends may be used.

Electrical connection
A qualified person in accordance with the Institute Of Electrical Engineers Regulations should connect the unit to the appropriate mains supply taking into account all the electrical information provided.

IMPORTANT – All pump systems must be used with an appropriate motor rated protection device.

The AutoFlush 90 XL requires minimal maintenance. Basic common sense and good housekeeping will ensure the best results. It is recommended that the unit be rinsed through with warm water and a minimum of bleach and washing up liquid added (approx. every 1–2 weeks). This should stop any milk residue and other fatty deposits being allowed to accumulate, go rancid and produce bad odours.

Once or twice yearly it is recommended that the unit be inspected. The lid should be removed and the tank and float cleaned.

Health & safety
As with all site work, the danger of working with water and electricity can pose a severe threat to health if obvious and fundamental precautions are not taken. Therefore if you are in any doubt regarding the installation, please contact us.

All site work must be undertaken by qualified personnel only.

These notes are for guidance only and it is for the installer to ensure the installation is in accordance with all structural and regulatory requirements.

Our policy is one of continuous product improvement, we reserve the right to change specifications and prices without prior notice. All information is given in good faith.

AquaSafe Alarm ‘Mini’

Price: £235.00


Telemetry System (Hard Wired)

Price: £675.00

Telemetry System (GSM)

Price: £970.00