Omni Pump International Limited t/a Edincare Pumped Drainage Sys
 01442 211 554
 
Product Search:   Go

MagnaCutter (150 Model)


View larger image

Price: £1,395.00 (£1,674.00 inc. VAT)
3101
2-3 working days
12 months

 
Description
Downloadable Documents
Related products

The Magna 150 Cutter is a fully automatic small bore pumping station suitable for pumping both foul and storm water to a higher level when gravity drainage is not possible or economical to install.

The system is suitable for installing either at the initial building stage or retro fitting to existing buildings and can accept waste from a bathroom, kitchen, basement, changing room or similar.

The system consists of a polyethylene tank, locking access cover, internal pipework and fittings with a built in automatic macerating submersible pump.

The Magna 150 Cutter is easy to install as inlets can be positioned to your requirements (inlet information to be supplied at time of order).

150 litre storage capacity.

Dimensions

 Model
Length
Width
Height
Magna150Cutter
700mm
550mm
550mm

Specification
 Model
Magna150Cutter
Power Supply
230V AC
Rated Current
6.4A
Motor Rating
1000W
Frequency
50Hz
Revolutions per Minute
2900rpm
Max. Vertical Output
21m
Max. Horizontal Output
250m
Max Flow Rate
132 l/m
Max. Liquid Temperature
<40°C
Discharge Size
32mm OD
Cable Length
5m
Weight
40kg
Colour
White

Also available in Three Phase (400V AC), please call for technical specifications.

Installation guidelines
It is important to note that these instructions are for guidance only. Please refer to the full Installation and Operating Guidelines when specifying / installing the product.

Siting the product
The Magna 150 Cutter is designed to be installed below ground level and so the prevailing ground conditions must be considered prior to locating the unit. Where possible, installation of a pumping station in a roadway should be avoided due to the need for periodic maintenance of the pump contained therein. If the location is adjacent to a roadway, the installation method should take into account the imposed loads likely to be transmitted to the tank by traffic etc.

The Magna 150 Cutter should be positioned in a sump with a firm level base and of sufficient dimensions to allow for a concrete surround.

Inlet connection
The Magna 150 Cutter comes complete with a 110mm rubber connector located on the side of the tank that will accept 110mm uPVC soil waste pipe. The waste pipe needs to be run with sufficient gradient to allow the waste to gravity drain into the unit and should be pushed firmly into the 110mm rubber connector so as to form a watertight seal around the incoming pipe.

NOTE – A 110mm inlet is positioned on the opposite side to the discharge oulet. Should you require a different position / diameter this must be specified at time of order.
 
Discharge connection
The connection of the discharge line is via the supplied compression adaptor. This connector is designed to accept black MDPE / HDPE pipework of appropriate outer diameter.

Electrical connection
A qualified person in accordance with the Institute Of Electrical Engineers Regulations should connect the unit to the appropriate mains supply taking into account all the electrical information provided.

IMPORTANT – All pump systems must be used with an appropriate motor rated protection device.

Maintenance
We recommend that the unit be inspected every three months. The inside of the Magna 150 Cutter unit should be inspected to ensure the floats are clean and free of any build up of materials that may inhibit the operation of the float switch. Also the moving parts of the pump should be checked to ensure that they are moving freely. Hose down the interior of the tank if necessary to remove any build up of solid materials and the bottom of the tank should be checked to make sure there is no debris or materials that could enter the pump and cause irreparable damage.

In addition we recommend that a service agreement be taken out with a technically qualified company.

Health & safety
As with all site work, the danger of working with water and electricity can pose a severe threat to health if obvious and fundamental precautions are not taken. Therefore if you are in any doubt regarding the installation, please contact us.

All site work must be undertaken by qualified personnel only.

These notes are for guidance only and it is for the installer to ensure the installation is in accordance with all structural and regulatory requirements.

Our policy is one of continuous product improvement, we reserve the right to change specifications and prices without prior notice. All information is given in good faith.


Compression - Straight Coupler 32mm

Price: £12.00

 

Compression - Elbow 32mm (90 deg)

Price: £12.00


Access Cover, Double Sealed, Locking, Inlay 600mm x 450mm (5 Tonne)

Price: £94.00

 

AquaSafe Alarm 'Sump'

Price: £325.00


MDPE Black Discharge Pipe Work 32mm OD x 25 Metres

Price: £62.00

 

MDPE Black Discharge Pipe Work 32mm OD x 50 Metres

Price: £122.00

Loading...