Omni Pump International Limited t/a Edincare Pumped Drainage Sys
 01442 211 554
 
Product Search:   Go

AutoFlush SS Pro


View larger image

Price: £1,495.00 (£1,794.00 inc. VAT)
2035
6-10 working days
12 months

 
Description
Downloadable Documents
Related products

The AutoFlush SS Pro is a fully automatic waste water pumping system with stainless steel tank suitable for pumping grey water to a higher level when gravity drainage is not possible or economical to install. The system offers a higher head and flow rate than the standard AutoFlush SS range.

The system is suitable for installing either at the initial building stage or retro fitting to existing buildings and can accept waste connections from a domestic sink, washing machine, dishwasher or similar.

The system consists of a stainless steel odour tight tank with a built in automatic waste water submersible pump.

The AutoFlush SS Pro is easy to install as inlets and outlet are prethreaded for connection of standard BSP fittings.

90 litre storage capacity

Dimensions 

 Model
Length
Width
Height
AutoFlushSS Pro
600mm
400mm
450mm

Specification
 Model
AutoFlushSS Pro
Power Supply
230V AC
Rated Current
3.6A
Motor Rating
700W
Frequency
50Hz
Revolutions per Minute
2800rpm
Max. Vertical Output
12m
Max. Horizontal Output
100m
Horizontal Fall
1:200
Max. Flow Rate
240 l/m
Max. Liquid Temp.
<40°C
Discharge Size
 1 1/2"
Cable Length
5m
Weight
31.5kg
Colour
Silver

Installation guidelines
It is important to note that these instructions are for guidance only. Please refer to the full Installation and Operating Guidelines when specifying / installing the product.
 
Siting the product
The AutoFlush SS Pro should be positioned on a firm level surface, resistant to condensation. The unit must be located lower than the outflow of the appliances served so as to provide a gravity fall into the unit.

It is extremely important to site the AutoFlush SS Pro with access in mind in the event of maintenance being required.

Inlet connections
The AutoFlush SS Pro comes as standard complete with 2no. 2" BSP threaded connections located at either end of the unit, and 1 no. 1 1/2" BSP threaded connection located in the lid. These are designed to accept uPVC fittings.

Discharge connection
The discharge line must be connected to the AutoFlush SS Pro via 1 1/2" BSP threaded connection on the side of the unit. This is designed to accept 1 1/2" PVC (Class E) high pressure fittings.
All joins in the discharge line must be made with solvent cement, under no circumstances should push fit or compression fittings be used.

The AutoFlush SS Pro is designed for one lift only and the vertical lift should be within 500mm of the unit.

IMPORTANT – It is recommended that there are no bends in the vertical lift, however if this is unavoidable a minimum of slow radius bends may be used.

Venting
The unit requires venting to atmosphere (no Durgo valve is to be used), if this is not possible we can supply a micro vent kit (optional extra) to enable the installer to vent within the building itself.

Electrical connection
A qualified person in accordance with the Institute Of Electrical Engineers Regulations should connect the unit to the appropriate mains supply taking into account all the electrical information provided.

IMPORTANT – All pump systems must be used with an appropriate motor rated protection device.

Maintenance
The AutoFlush SS Pro requires minimal maintenance. Basic common sense and good housekeeping will ensure the best results. It is recommended that the unit be rinsed through with warm water and a minimum of bleach and washing up liquid added (approx. every 1–2 weeks). This should stop any milk residue and other fatty deposits being allowed to accumulate, go rancid and produce bad odours.

Once or twice yearly it is recommended that the unit be inspected. The lid should be removed and the tank and float cleaned.

Health & safety
As with all site work, the danger of working with water and electricity can pose a severe threat to health if obvious and fundamental precautions are not taken. Therefore if you are in any doubt regarding the installation, please contact us.

All site work must be undertaken by qualified personnel only.

These notes are for guidance only and it is for the installer to ensure the installation is in accordance with all structural and regulatory requirements.

Our policy is one of continuous product improvement, we reserve the right to change specifications and prices without prior notice. All information is given in good faith.


AquaSafe Alarm ‘Mini’

Price: £225.00

 

Telemetry System (Hard Wired)

Price: £645.00


Telemetry System (GSM)

Price: £945.00

 

Micro Vent Kit

Price: £155.00

Loading...