Omni Pump International Limited t/a Edincare Pumped Drainage Sys
 01442 211 554
 
Product Search:   Go

AquaFlush MF


View larger image

Price: £635.00 (£762.00 inc. VAT)
2072
4-5 working days
12 months

 
Description
Downloadable Documents
Related products

The AquaFlush MF is a fully automatic waste water pumping system suitable for pumping grey water to a higher level when gravity drainage is not possible or economical to install.

The system is suitable for installing either at the initial building stage or retro fitting to existing buildings and can accept waste connections from a sink, washing machine, dishwasher or similar.

The system consists of an odour tight tank with a built in automatic waste water submersible pump.

The AquaFlush MF is easy to install as there are five pre-moulded inlets, 2 either side and 1 located on the top of the system.

Dimensions

 Model
Length
Width
Height
AquaFlushMF
345mm
400mm
390mm

Specification
 Model
AquaFlushMF
Power Supply
230V AC
Rated Current
3A
Motor Rating
660W
Frequency
50Hz
Revolutions per Minute
2900rpm
Max. Vertical Output
11m
Max. Horizontal Output
80m
Horizontal Fall
1:200
Max. Flow Rate
180 l/m
Max. Liquid Temp.
<60°C intermittent
Discharge Size
32mm
Cable Length
3m
Weight
11kg
Colour
White

Installation guidelines
It is important to note that these instructions are for guidance only. Please refer to the full Installation and Operating Guidelines when specifying / installing the product.

Siting the product
The AquaFlush MF should be positioned on a firm level surface, resistant to condensation. The unit must be located lower than the outflow of the appliances served so as to provide a gravity fall into the unit.

It is extremely important to site the AquaFlush MF with access in mind in the event of maintenance being required.

Inlet connections
The AquaFlush MF comes complete with 5 inlet connection ports and rubber seals to suit 32/40mm uPVC waste pipe. The incoming pipework from the appliances served should be pushed into the rubber seal approximately 30mm, which will then form a watertight seal around the pipework.

Blanking caps and seals are provided to seal off any of the pre-cut inlets that are not required.

Discharge connection
The discharge line can exit through either the left or right hand side of the unit by rotating the rubber bend on the pump to suit. The connecting pipework must be 32mm PVC waste pipe and should be pushed into the non-return valve and secured into place using the jubilee clips provided.

All joins in the discharge line must be made using solvent cement, under no circumstances should push fit or compression fittings be used.

The AquaFlush MF is designed for one lift only and the vertical lift must be made within 500mm of the unit.

IMPORTANT – It is recommended that there are no bends in the vertical lift, however if this is unavoidable a minimum of slow radius bends may be used.

Electrical connection
A qualified person in accordance with the Institute Of Electrical Engineers Regulations should connect the unit to the appropriate mains supply taking into account all the electrical information provided.

IMPORTANT – All pump systems must be used with an appropriate motor rated protection device.

Maintenance
The AquaFlush MF requires minimal maintenance. Basic common sense and good housekeeping will ensure the best results. It is recommended that the unit be rinsed through with warm water and a minimum of bleach and washing up liquid added (approx. every 1–2 weeks). This should stop any milk residue and other fatty deposits being allowed to accumulate, go rancid and produce bad odours.

Once or twice yearly it is recommended that the unit be inspected. The lid should be removed and the tank and float cleaned.

Health & safety
As with all site work, the danger of working with water and electricity can pose a severe threat to health if obvious and fundamental precautions are not taken. Therefore if you are in any doubt regarding the installation, please contact us.

All site work must be undertaken by qualified personnel only.

These notes are for guidance only and it is for the installer to ensure the installation is in accordance with all structural and regulatory requirements.

Our policy is one of continuous product improvement, we reserve the right to change specifications and prices without prior notice. All information is given in good faith.


Telemetry System (GSM)

Price: £945.00

 

AquaSafe Alarm ‘Mini’

Price: £225.00


Telemetry System (Hard Wired)

Price: £645.00

   
Loading...